Control Arm ZF-HD-1014/ZF-3105 M20100082
Control Arm ZF-HD-1014/ZF-3105 (M20100082) for Hyundai — OE 54500-1R000, left hand. Suspension control arm, factory direct, MOQ 50 pcs per part number.
Product Overview
This control arm is a direct-fit replacement for Hyundai applications and carries the factory part number ZF-HD-1014/ZF-3105 (left hand). It is manufactured from forged or cast steel (or aluminium on some applications) with a pressed-in rubber or hydraulic bushing at the subframe end and a sealed ball joint at the hub end, ball-joint boots filled with molybdenum grease and the whole arm coated against road salt. The arm connects the wheel hub to the subframe and locates the wheel fore-and-aft and in camber, so the tyre stays planted through cornering and braking; the bushings isolate road noise while the ball joint lets the hub steer.
Published OE references: 54500-1R000, 54500-0U000, 54500-1R100, 54500-4L000.
Applications listed by the factory: DODGE / ATTITUDE / II, 2012 - 2014 Control arm HYUNDAI / ACCENT BLUE / , 2012 -.
Key Features
Typical Applications
Match the OE number first, then confirm the fitment side (left/right) and check the ball-joint taper and the bushing bore diameter against the old arm. Control arms are handed on most applications — a left arm will not fit the right side even though the two look similar. Always replace both sides together and have the alignment re-set afterwards.
Applications and Selection Guide
Use the available OE and product data below to shortlist this part, then confirm final fitment before ordering.
| Selection point | Control Arm ZF-HD-1014/ZF-3105 M20100082 option | What the project must confirm |
|---|---|---|
| Product code | M20100082 | Match the requested part number and version |
| OE references | 54500-1R000,54500-0U000,54500-1R100,54500-4L000 | Check the original part number and cross-reference |
| Vehicle references | Hyundai,Dodge | Confirm model, year, engine and market |
| Dimensions | On request | Compare the current drawing or approved sample |
| Thread / interface | Confirm by drawing | Compare the fitting interface with the approved part |
OE Reference
Compare the original part number and any published cross-references with the required vehicle part.
Vehicle Application
Confirm vehicle model, engine, production year and destination market before ordering.
Dimensions and Interface
Check the product drawing, measurements and connection or thread details.
Order Configuration
Agree on quantity, marking, packaging and documents for the approved product.
Ordering Guide
- Specify product code M20100082.
- Provide the original part number and vehicle information.
- Confirm dimensions, thread or interface against the drawing or sample.
- State target quantity, branding, packaging and destination market.
- Request a quotation and sample for final approval.
Fitment and Quality Checks
- Verify the original part number and approved cross-reference.
- Compare dimensions and connection details with the current drawing.
- Confirm the vehicle application and any market-specific requirements.
- Review samples, marking and packaging before the production order.
Technical Specifications
| Parameter | Published product data |
|---|---|
| Product code | M20100082 |
| Product category | Control Arms |
| OE references | 54500-1R000,54500-0U000,54500-1R100,54500-4L000 |
| Position | Left |
| Vehicles | Hyundai,Dodge |
Product Matching Checklist
| Item | Buyer information | Makexcar review |
|---|---|---|
| OE reference | Original part number | Cross-reference and sample check |
| Vehicle | Model, year and engine | Application confirmation |
| Dimensions | Drawing or existing part | Measurement comparison |
| Order | Quantity and destination | Packaging and document review |
Final fitment must be confirmed against the current specification and approved sample.
Order Information
| Requirement | Details to provide |
|---|---|
| Product | M20100082 |
| Part reference | 54500-1R000,54500-0U000,54500-1R100,54500-4L000 |
| Application | Hyundai,Dodge |
| Commercial terms | Quantity, destination and packaging requirements |
Why Choose Makexcar
Published manufacturing standard: IATF 16949 and ISO 9001 production; every arm is checked for straightness, the ball joint is torque-tested and the boot is leak-tested before packing. Request current product documents and samples for the ordered configuration.
50
MOQ
Pieces per part number
15–25
LEAD TIME
Working days after deposit
OE
PART MATCHING
Check published OE references
NEW
CONDITION
New replacement component
Automated Production
Testing Equipment
Packaging Review
Quality Inspection
What Can We Customize?
Private label, custom packaging, barcode and OEM numbering available from 500 pcs per part number
Logo & Branding
Private-label marking and artwork are subject to sample approval.
Packaging Customization
Discuss boxes, labels, manuals and cartons for the destination market.
Product Specification
Review the approved part specification and available options.
Product Appearance
Discuss appearance and marking for the approved product configuration.
Documentation Support
Request available drawings, test data and management certificates.
Engineering Review
Provide a sample or drawing for matching and project feasibility review.
Control Arm ZF-HD-1014/ZF-3105 M20100082 Product FAQ
What does this product code identify?
Product code M20100082 is used for quotation and document requests.
How do I confirm fitment?
Match the OE number first, then confirm the fitment side (left/right) and check the ball-joint taper and the bushing bore diameter against the old arm. Control arms are handed on most applications — a left arm will not fit the right side even though the two look similar. Always replace both sides together and have the alignment re-set afterwards.
What measurements should I check?
The source catalogue does not publish exterior dimensions for this part; match the OE number and vehicle application, then request a drawing or sample.
Are private-label orders available?
Branding and packaging can be reviewed against the approved specification and quantity.
Can I request a sample?
Send the product code, target quantity and destination market through the contact form.
What technical documents are available?
Ask Makexcar for current drawings, product data and available test documents for your configuration.
Confirm the Right Control Arm ZF-HD-1014/ZF-3105 M20100082
Send the part reference, vehicle application, quantity and packaging requirements for review.
